Resistivity Rod Set

Description Simplify your experimental setup with the Go Direct Current Probe. It connects wirelessly via Bluetooth® or wired via USB to your device. The wireless connection eliminates additional cables that can clutter the lab bench. Capture small currents like those produced by a magnet falling through a coil. Use in combination with the Go Direct Voltage Probe to investigate Ohm’s law or series and parallel circuits. Explore RC and RLC circuits. Rechargeable Battery—Ready When You Are The robust rechargeable battery offers long battery life and provides always-ready operation when using the sensor wirelessly. Monitor battery life directly from our free Graphical Analysis™ 4 app or LabQuest 2 App. Should the battery run low, simply connect the sensor to the charging cable and keep on collecting—no interruptions or inconvenience to you or your students. Wired or Wireless—The Flexibility to Choose Our Go Direct sensors connect directly to your mobile device, Chromebook™, or computer using our free Graphical Analysis™ 4 app—no additional equipment or software purchases are necessary. Go Direct sensors can be used wired via USB or wirelessly via Bluetooth® wireless technology, allowing you to choose the solution best for your classroom or laboratory.   Specifications Range: +/- 1 A and +/- 0.1 A Maximum non-damaging current: 1.5 A and 0.5 A Typical resolution: 0.031 mA and 0.003 mA Connections: Wireless: Bluetooth Wired: USB

The Current Probe can be used to measure currents in low-voltage AC and DC circuits or for electrochemistry experiments. The Current Probe measures DC and low-frequency AC currents up to 600 mA. Use Current Probes in combination with Differential Voltage Probes to investigate Ohm’s Law and explore series and parallel circuits. The 0.1 Ω shunt resistor minimizes changes to your circuit. If currents will exceed 1 A, use the High Current Sensor. Range: ±0.6 A Maximum voltage on any input: ±10 V User Manual

Mit Hilfe der zweiten Experimentierplatine von Vernier kann mit einfachen elektrischen Schaltkreisen experimentiert werden. Die Platine ist bestückt mit Kondensatoren, Widerständen, einer LED, Schaltern, Batteriehaltern, einem Anschluss für die externe Spannungsversorgung, einer selbstrückstellenden Sicherung, Lämpchensockeln, Anschlussmöglichkeiten für weitere Bauteile und Anschlusspins, die den Anschluss von Krokodilklemmen vereinfachen. Description The Vernier Circuit Board 2 is a basic electricity lab on a board. The turret terminals for every component make it easy to connect basic series and parallel circuits, examine the behavior of different components, and investigate RLC circuits. The Vernier Circuit Board 2 includes 10 bulbs, a resettable fuse, three powering options, 10 alligator clip leads, terminal clips to add your own components, and pre-installed components. Installed Components R1 and R2–10 Ω resistors rated at 5 W R3 and R4–51 Ω resistors rated at 2 W R5 and R6–68 Ω resistors rated at 2 W R7–22 kΩ resistor rated at 1 W R8–47 kΩ resistor rated at 1 W R9–100 kΩ resistor rated at 1 W R11–4.7 kΩ resistor rated at 1 W C1–1 µF non-polar capacitor C2–10 µF non-polar capacitor 3 E-10 lamp sockets LED and 220 Ω current limiting resistor L1–5 mH inductor, with powdered iron core in a clip 1 kΩ linear potentiometer 85 dB buzzer SW2–single-pole, double-throw (SPDT) switch SW3–single-pole, single-throw (SPST) momentary switch The Vernier Circuit Board 2 can be used interchangeably with the Vernier Circuit Board in experiments included in Physics with Vernier and Advanced Physics with Vernier–Beyond Mechanics. Specifications Size: 10 in. x 6.5 in. (25.5 cm x 16.5 cm) Mass: ~0.44 kg Optional power sources: up to 4 AA batteries, not included LabQuest Power Supply, not included (or other 5 VDC adapter with center-positive ⅛ inch connector) DC power supply Vernier Power Amplifier Maximum voltage: 10 V Resettable fuse opens at 0.8 A, but 0.3 A or less is recommended All parts ROHS compliant What’s Included One circuit board Ten insulated jumper wires fitted with mini-alligator clips Five #48 lamps rated 0.06 A at 2.0 V (cylindrical body) Five #50 lamps rated 0.220 A at 7.5 V (round body)

The Instrumentation Amplifier can be used to connect a wide variety of measurement equipment to a Vernier interface and electronically collect, store, and analyze the data. The Instrumentation Amplifier monitors voltages from 20 mV to 1 V (DC or AC). It has several switch settings to allow you to select the best gain and includes auto-ID functionality for each of the six ranges. Input bandwidth of 10 kHz allows the capture of higher frequency signals. It is typically used to amplify the chart recorder or analog output of any instrument, such as a third-party gas chromatograph. Range settings:0-20 mV, 0-200 mV, 0-1 V, ±20 mV, ±200 mV, ±1 V User manual

Use Vernier probeware to teach concepts at the college physics, Advanced Placement (AP) Physics, or International Baccalaureate (IB) Physics level. Use it in addition to Advanced Physics with Vernier - Mechanics (PHYS-AM) and Physics with Vernier (PWC-LP) for a comprehensive set of topics. Advanced Physics with Vernier – Beyond Mechanics is the second of a two-volume set of experiments for the more in-depth introductory physics course, such as college physics, AP Physics, or IB Physics. Experiments are designed for an interactive teaching style, with planned moments for instructor or student-led discussion. Instructor notes include discussion on how to lead students to a successful activity. The book includes many extensions to challenge the most talented students.