Physik mit Vernier - RESTBESTAND

Mit Hilfe der zweiten Experimentierplatine von Vernier kann mit einfachen elektrischen Schaltkreisen experimentiert werden. Die Platine ist bestückt mit Kondensatoren, Widerständen, einer LED, Schaltern, Batteriehaltern, einem Anschluss für die externe Spannungsversorgung, einer selbstrückstellenden Sicherung, Lämpchensockeln, Anschlussmöglichkeiten für weitere Bauteile und Anschlusspins, die den Anschluss von Krokodilklemmen vereinfachen. Description The Vernier Circuit Board 2 is a basic electricity lab on a board. The turret terminals for every component make it easy to connect basic series and parallel circuits, examine the behavior of different components, and investigate RLC circuits. The Vernier Circuit Board 2 includes 10 bulbs, a resettable fuse, three powering options, 10 alligator clip leads, terminal clips to add your own components, and pre-installed components. Installed Components R1 and R2–10 Ω resistors rated at 5 W R3 and R4–51 Ω resistors rated at 2 W R5 and R6–68 Ω resistors rated at 2 W R7–22 kΩ resistor rated at 1 W R8–47 kΩ resistor rated at 1 W R9–100 kΩ resistor rated at 1 W R11–4.7 kΩ resistor rated at 1 W C1–1 µF non-polar capacitor C2–10 µF non-polar capacitor 3 E-10 lamp sockets LED and 220 Ω current limiting resistor L1–5 mH inductor, with powdered iron core in a clip 1 kΩ linear potentiometer 85 dB buzzer SW2–single-pole, double-throw (SPDT) switch SW3–single-pole, single-throw (SPST) momentary switch The Vernier Circuit Board 2 can be used interchangeably with the Vernier Circuit Board in experiments included in Physics with Vernier and Advanced Physics with Vernier–Beyond Mechanics. Specifications Size: 10 in. x 6.5 in. (25.5 cm x 16.5 cm) Mass: ~0.44 kg Optional power sources: up to 4 AA batteries, not included LabQuest Power Supply, not included (or other 5 VDC adapter with center-positive ⅛ inch connector) DC power supply Vernier Power Amplifier Maximum voltage: 10 V Resettable fuse opens at 0.8 A, but 0.3 A or less is recommended All parts ROHS compliant What’s Included One circuit board Ten insulated jumper wires fitted with mini-alligator clips Five #48 lamps rated 0.06 A at 2.0 V (cylindrical body) Five #50 lamps rated 0.220 A at 7.5 V (round body)

Description This sensor has an exposed thermistor that results in an extremely rapid response time, and this design allows for use in air and water.  Use this sensor in a variety of experiments:   Investigate the effect of temperature on solar panel output. Explore passive solar heating or solar collectors. Examine the warming function of nasal passageways. Discover the effect of vascularity on skin temperature recovery. Important: For use in air and water only. For temperature measurements in harsher environments that require a more durable probe, we recommend the Go Direct® Temperature Probe.  Rechargeable Battery—Ready When You Are The robust rechargeable battery offers long battery life and provides always-ready operation when using the sensor wirelessly. Monitor battery life directly from our free Graphical Analysis™ 4 app or LabQuest 2 App. Should the battery run low, simply connect the sensor to the charging cable and keep on collecting—no interruptions or inconvenience to you or your students. Wired or Wireless—The Flexibility to Choose Our Go Direct sensors connect directly to your mobile device, Chromebook™, or computer using our free Graphical Analysis™ 4 app—no additional equipment or software purchases are necessary. Go Direct sensors can be used wired via USB or wirelessly via Bluetooth® wireless technology, allowing you to choose the solution best for your classroom or laboratory.   Specifications Range: –25 to 125°C Maximum temperature that the sensor can tolerate without damage: 150°C Accuracy: ±0.5°C Response time (from 25°C to 100°C in water): 5 seconds Probe dimensions: Probe handle: Length: 6.8 cm Width: 2.25 cm Thickness: 1.3 cm Cable length: 1 m Connections: Wireless: Bluetooth Wired: USB

This Voltage Probe can be used with the Vernier LabPro, LabQuest, LabQuest Mini, Go!Link, Easylink, SensorDAQ and CBL 2 to measure direct voltage. The Voltage Probe is a bipolar sensor. The black lead is grounded along with the interface, and the sensor reports the potential difference between the red lead and ground. It can be used to measure the potential in DC or AC circuits. You might also consider the Differential Voltage Probe (DVP-BTA). Multiple Differential Voltage Probes can be connected to a circuit without the use of a common grounding terminal. Input voltage range:± 10 V User manual

Description Monitor angular motion easily and precisely with the Go Direct Rotary Motion Sensor, which connects wirelessly via Bluetooth® or wired via USB to your device. The wireless connection eliminates the cables that can get caught and tangled during rotational investigations.  Determine position, velocity, and acceleration of objects in angular motion. Measure angle increments as small as 0.25°. Investigate rotational dynamics, conservation of angular momentum, pendulum motion, polarization of light, and more. Rechargeable Battery—Ready When You Are The robust rechargeable battery offers long battery life and provides always-ready operation when using the sensor wirelessly. Monitor battery life directly from our free Graphical Analysis™ 4 app or LabQuest 2 App. Should the battery run low, simply connect the sensor to the charging cable and keep on collecting—no interruptions or inconvenience to you or your students.  Wired or Wireless—The Flexibility to Choose Our Go Direct sensors connect directly to your mobile device, Chromebook™, or computer using our free Graphical Analysis™ 4 app—no additional equipment or software purchases are necessary. Go Direct sensors can be used wired via USB or wirelessly via Bluetooth® wireless technology, allowing you to choose the solution best for your classroom or laboratory.  Specifications Resolution: 1° or 0.25° Optical Encoder: Bidirectional, quadrature encoder Maximum Speed: 30 rev/s at 1° resolution 7.5 rev/s at 0.25° resolution 3-step Pulley: 10 mm, 29 mm and 48 mm groove diameter, 55 mm with O ring in groove Connections: Wireless: Bluetooth Wired: USB

Recueillez des données d'accélération, de rotation et d'altitude en classe ou sur le terrain. Go Direct Acceleration se connecte sans fil à votre appareil par Bluetooth® ou par câble USB. Ce capteur d'accélération à 3 axes possède deux plages d'accélération, ainsi qu'un altimètre et un gyroscope à 3 axes. Mesurez les impacts du casque lors d'enquêtes reliées à une commotion cérébrale. Glissez-le dans votre poche et pirouettez-le ou montez en half-pipe. Attachez l'accéléromètre à votre bicyclette ou fixez-le à votre chariot de laboratoire sans faire traîner de câbles. Remarque: Les produits Vernier sont conçus à des fins éducatives. Nos produits ne sont pas conçus et ne sont pas recommandés pour des procédés industriels, médicaux ou commerciaux tels que le maintien de la vie, le diagnostic des patients, le contrôle d'un procédé de fabrication ou les essais industriels de quelque nature que ce soit. Spécifications Fourchette: Accélération faible: ±157 m/s2 (±16 g) Accélération élevée: ±1 960 m/s2 (±200 g) Gyroscopiques: ±2 000 °/s Altimètre: –1,800 m à 10,000 m (-5,900 ft à 33,000 ft) Angle: ±180° Connexions: Sans fil: Bluetooth Câblé: USB